Spent platinum-rhodium thermocouples are one of the most common Pt scrap streams in the glass, steel, chemical and semiconductor industries. The metal content is high, the alloy composition is known from the type designation, and even heavily drifted wire retains nearly all of its precious metal. Yet sellers routinely leave money on the table — usually by mixing thermocouple types, shipping them with ceramic insulators still attached, or discarding “contaminated” sections that are still fully payable. Here is what your wire is worth, and how to hand it over so you are paid for all of it.
Which Thermocouples Contain Platinum and Rhodium?
Noble-metal thermocouples — types S, R and B — are built from platinum-rhodium alloys precisely because they survive where base-metal types fail: extreme and sustained high temperature, oxidising atmospheres, and demanding accuracy. Common grades we buy:
- Type B: Pt-30%Rh positive leg / Pt-6%Rh negative leg (30/6)
- Type R: Pt-13%Rh positive leg / pure Pt negative leg
- Type S: Pt-10%Rh positive leg / pure Pt negative leg
- Bare Pt-Rh wire, used couple assemblies, broken heads and contaminated sections
| Type | Positive leg | Negative leg | Typical service |
|---|---|---|---|
| S | Pt-10% Rh | Pure Pt | Steel, glass, lab furnaces (~1,600 °C class) |
| R | Pt-13% Rh | Pure Pt | Higher-accuracy industrial duty |
| B | Pt-30% Rh | Pt-6% Rh | Very high temperatures, both legs alloyed |
The value difference between these types is substantial — a type B wire carries far more rhodium per metre than a type S. Because rhodium is priced far above platinum, knowing which type you hold is the first driver of your payout. If the type markings have worn off, an experienced recycler can identify the alloy from the assay; that is another reason a proper ICP analysis matters (see our comparison of ICP and XRF assay methods).
Grading Matters — and So Does Honest Grading
The value of a thermocouple lot depends almost entirely on the Rh percentage. Mis-graded lots (e.g. selling a Type R couple as Type S, or mixing in Pt-2Rh legs) can mean a large loss for the seller — “conservatively” pricing an unknown mix can cost a double-digit percentage of your payout. That is why every Litop PGMs lot is assayed by ICP-AES: you are paid on the measured Pt/Rh ratio, not on visual estimation.
Why Drifted or “Damaged” Wire Is Still Valuable
Thermocouples are replaced for electrical reasons — calibration drift, embrittlement, mechanical damage — not because the metal disappeared. Platinum and rhodium do not evaporate in normal service (contamination and grain growth affect the signal, not the inventory). In practice:
- Drifted wire still assays at specification in almost all cases. Do not discard discoloured or brittle sections — send them.
- Silver-grey “poisoned” patches often indicate rhodium or platinum pickup from the process environment, not metal loss.
- Wire that has touched molten metal or slag may carry adhering contamination — still payable, just sorted and noted separately.
The exception is gross mechanical loss: wire fragments embedded in furnace brick or swept into slag are genuinely gone. Recovering those is a different, lower-yield job — the same slag-recovery logic we describe for rhodium recovery rates.
The Three Mistakes That Cost Sellers the Most
1. Mixing thermocouple types in one lot
If types S, R and B are coiled together, the recycler must either assay the mix or price it conservatively at the lowest-value alloy. Coil each type separately, label it, and photograph the markings if they are still legible.
2. Shipping with ceramic insulators and sheaths still attached
Alumina insulator beads, protection tubes, and steel sheaths add weight without adding metal. They also complicate sampling. Strip the bare wire where practical — and if a buyer quotes on gross weight including ceramics, that alone should tell you to look elsewhere. Payable recovery is always based on assayed contained metal, as we explain in our guide to getting the best price for PGM scrap.
3. Selling to a buyer who cannot verify the alloy
Thermocouple alloys are a known, narrow range — which makes them easy to verify and also easy to misrepresent. Insist on an ICP-based assay with a written certificate. Our laboratory offers free ICP and XRF testing on incoming thermocouple lots precisely so that sellers can see the alloy content before agreeing to a price.
How the Recycling Process Works
- Sorting and inspection — wire is separated by type and condition, non-metal attachments are removed, and each lot is weighed and documented.
- Sampling and assay — the lot is melted or dissolved with a representative sample taken for ICP analysis; Pt and Rh contents are determined separately.
- Refining — platinum and rhodium are separated from each other and from trace impurities, then produced to high purity.
- Settlement — you are paid on assayed contained metal at market pricing, per the terms agreed before shipping. For international lots, the chain-of-custody rules in our international shipping guide apply.
Clean, sorted, bare thermocouple wire is one of the highest-recovery PGM scrap forms — which is why preparation before shipping pays for itself.
What We Also Buy
Beyond bare wire and complete couple assemblies, we purchase used ceramic insulator tubes containing Pt-Rh residues and furnace assemblies with embedded thermocouple wire. Related materials from the same high-temperature operations include spent iridium and platinum crucibles. Our dedicated service page covers the full thermocouple recycling and procurement process.
Preparation Checklist Before You Send Wire
- ☑ Coils separated by type (S / R / B), each labelled
- ☑ Ceramic insulators, tubes and sheaths removed where practical
- ☑ Damaged or drifted sections kept — not discarded
- ☑ Photos of markings and coils taken for your records
- ☑ Approximate weights per type noted
- ☑ Refiner’s assay method confirmed (ICP, written certificate, retained split)
Get a Quote for Your Thermocouple Wire
Have used thermocouple wire to sell? Send photos, the type markings if visible, and approximate weights — we will return an indicative quote with free assay testing: contact our refining team.
